Specification
Max. Pressure | 5,075 PSI 350 bar |
---|---|
Max. Speed | 100 RPM 100/min |
Max. Temperature | 205ºF 95ºC |
The CWF/EWF Series are small, lightweight, economical type optical data transmission devices that enable data to be transmitted quickly and reliably between an aligned pair of units over mid- range distances. Typical uses are on overhead and stacker cranes, automated storage and retrieval systems (AS/RS) and transfer cars for non-contact bi-directional communication from the vehicle to the control unit. The use of modulated light as the transfer method means that these transceivers do not incur physical wear like trailing cables and slip rings nor do they require recalibration like radio systems.
The DM Series are half-duplex parallel-type and full-duplex serial-type optical data transmission devices that enable data to be transmitted quickly and reliably between an aligned pair of units over short distances. Typical uses are on automated guided vehicles (AGV), rail-guided vehicles (RGV) and overhead transports (OHT) for providing a wireless link between the vehicle and a fixed docking station. Special models equipped with a 25-pin D-sub connector provide SEMI E84 compliance for interfacing between semiconductor process equipment and automated material handling systems (AMHS). Through a pulse-modulated light beam these transceivers can send 4, 8, 16-bit or serial signals simultaneously in both directions from the active and passive sides depending on the application requirements and model used.
1 to 6 pairs of optical sensors can be connected. DIN rail-mountable. Models with single/ double Muting and Override functions. Response time less than 5ms. 2 static PNP outputs (500 mA).
With integrated control unit; protected height from 150 mm to 1,800 mm; resolution 30 or 40 mm for hand detection; 50 or 90 mm for body detection. Models with 2, 3 or 4 beams for access control.
The open-network type optical data transmission devices enable data to be transmitted quickly and reliably via Ethernet, CC-Link or DeviceNet between an aligned pair of units over various distances. Typical uses are on stacker cranes, automated storage and retrieval systems (AS/RS), AGVs and transfer cars for non-contact communication from the vehicle to the control unit. The use of modulated light as the transfer method means that these transceivers do not incur physical wear like trailing cables and slip rings nor do they require recalibration like radio systems.
With integrated control unit; protected height from 150 mm to 1,800 mm; resolution 14 or 20 mm for finger detection; 30 or 40 mm for hand detection; 50 or 90 mm for body detection. Models with 2, 3 or 4 beams for access control.
From ø 6.5 mm to M30 diameter; shielded and unshielded models; standard and extended distance; cable, M8 plug or M12 plug output. Analogue models available.
Safety relay. Safety relay with Muting inputs. Support brackets, beam-steering mirrors; connection cables.
The BRS series of optical remote control technology is suitable for many applications requiring simple data transmission between an operator and machine. Featuring small hand-held transmitters and compact receiver units, these models provide reliable communication for distances up to 10 meters. These systems allow an operator to transmit a signal to one specific receiver or several receivers through designated codes. With the flexibility of one transmitter communicating to multiple receiver units, an operator can reduce the number of spare transmitters needed and increase the overall efficiency of the remote control system.
From ø 6.5 mm to M30 diameter; shielded and unshielded models; standard and extended distance; cable, M8 plug or M12 plug output. Analogue models available.
The KAD-300 crane collision avoidance sensor is used to reduce the potential for collisions between overhead cranes, monorail systems, and fixed objects or obstructions located in the crane runway area. Built with a rugged metal housing, this device offers three separate outputs for distance settings up to 100 feet and is used to initiate slow-down and stop commands. In addition to the three outputs, the KAD-300 is equipped with a trouble (FAULT) output that will energize in the event a failure occurs with the internal emitter and receiver components.
A typical application would have the sensor unit mounted on the crane bridge and a reflective target on the opposing end wall or crane. With limited hardware, the KAD-300 allows for an ease of installation and maintenance. The flexibility of this device will allow you to configure it to variable frequency drives and stepped controls.
The RSC-30LN scanning laser rangefinder is an industrial sensor used for area obstacle detection and collision prevention for high-bay to lower bay crane applications. With a wide scan angle and detection range, this scanner will reduce the potential for collisions between overhead cranes and fixed objects or obstructions located in the crane runway area. With area-setting software, this device can be easily configured to any application for programming up to three detection output zones.
for spraying-clamping-unclamping applications at steel-strip winders
In combination with SP0077 (2-Passage)
• grease is supplied to the winding mandrel tolubricate the moving elements of the winder
From ø 6.5 mm to M30 diameter; shielded and unshielded models; standard and extended distance; cable, M8 plug or M12 plug output. Analogue models available.
The Hokuyo LAV series is a laser-based optical fiber type hot metal detector (HMD) that contains a separately housed emitter and receiver, heat-resistant fiber cables and heavy-duty sensor heads. Equipped with high-powered laser diodes, this device operates effectively in high-temperature harsh production areas where dust, steam and vapors are present. With accurate long-range transmission, this through-beam system operates effectively in mill environments by detecting passing material on a process line that interrupts the infrared laser beam.
The Hokuyo MBX series is a non-contact hot metal detector (HMD) that uses microwave transmission for detecting hot steel. This system integrates a control unit, stainless waveguide and remotely mounted antenna stand. For the most severe applications where dust, smoke, vapors, high temperatures, induced noise or intense ambient light are present, this non-invasive sensing system is ideal for reliable detection of hot material in a continuous casting line, pipe or rolling mill.
From ø 6.5 mm to M30 diameter; shielded and unshielded models; standard and extended distance; cable, M8 plug or M12 plug output. Analogue models available.
3G communication
920MHz communication
for clamping-unclamping applications at steel-strip winders
In combination with SP0077 (2-Passage)
• grease is supplied to the winding mandrel to lubricate the moving elements of the winder
The Hokuyo PX-DX/WX series is an economical through-beam type hot metal detector (HMD) that is used where lower ambient temperature areas are present within the steel manufacturing process. This model consists of a separate emitter and receiver equipped in compact self-contained housings. With accurate long-range transmission, this through-beam sensor operates effectively in mill environments by detecting passing material on a process line that interrupts the modulated light beam.
For clamping-unclamping applications at steel-strip winders
Max. Pressure | 5,075 PSI 350 bar |
---|---|
Max. Speed | 100 RPM 100/min |
Max. Temperature | 205ºF 95ºC |
The PHV-10 series is an LED-based optical fiber type hot metal detector (HMD) that contains a separately housed emitter and receiver, heat-resistant fiber cables and heavy-duty sensor heads. With accurate long-range transmission, this through-beam system operates effectively in mill environments by detecting passing material on a process line that interrupts the modulated light beam.
From ø 6.5 mm to M30 diameter; shielded and unshielded models; standard and extended distance; cable, M8 plug or M12 plug output. Analogue models available.
The PRV-10 series Hot Metal Detector (HMD) is an electronic controller that includes the infrared detection cell, amplifier and electronic outputs in an aluminum die-cast housing. To accommodate variation in product temperature and background radiation, three levels of infrared thresholds are selectable with an internal switch and sensitivity adjustment knob. Combined with flexible stainless steel fiber cables and interchangeable sensor heads, this radiant-heat detection system can be standardized throughout the mill.
Models with 0 – 300 mm or 0 – 1,100 mm sensing distance range. Housing with reduced dimensions. Cable exit.
With integrated control unit; protected height from 150 mm to 1,800 mm; resolution 30 or 40 mm for hand detection; 50 or 90 mm for body detection. Models with 2, 3 or 4 beams for access control.
With integrated control unit; protected height from 150 mm to 1,800 mm; resolution 14 or 20 mm for finger detection; 30 or 40 mm for hand detection; 50 or 90 mm for body detection. Models with 2, 3 or 4 beams for access control.
Safety relay. Safety relay with Muting inputs. Support brackets, beam-steering mirrors; connection cables.
1 to 6 pairs of optical sensors can be connected. DIN rail-mountable. Models with single/ double Muting and Override functions. Response time less than 5 ms. 2 static PNP outputs (500 mA).
NiDEX Swithching Power Supply – Economic and Realible
M18 single-beam sensors with 10 m (axial optics) or 5 m (radial optics) operating distance. M30 single-beam sensors with up to 60 m operating distance. Models with plastic or metal housing. Glass optics (more resistant to dust particle accumulation and abrasion). Models SH/TH_IA to be used in particular with the safety control unit SBCR03.
Aluminium housing; controlled height 70 mm; 0.3 m to 4.5 m sensing distance range; smallest detectable object 2 mm; red polarized emission; teach adjustment. Models with IO-LINK technology.
Compact sensor in aluminium, height varying form 160 mm to 960 mm; crossed or parallel beams; up to 6 m operating distance; 5, 10 and 20 mm pitch; smallest detectable object 1.5 mm; digital and analogue output; teach adjustment; optical and cable synchronization.
Compact sensor with plastic housing; 6 mm to 30 mm pitch; crossed beam detection up to 90 mm height; maximum sensing distance 6 m. ATEX models 3 GD and 2 GD available; wide range of special models.
Without housing; controlled height 140 and 160 mm; up to 2 m sensing distance range; 10 mm pitch; axial or radial optics; maximum resolution 5 mm; trimmer adjustment; tropicalization available.
From Miniaturized size to Maxi size, with red and infrared emissions. Wide range of models available: adjustable with background suppression, direct diffuse, retroreflective, polarized, for transparent objects and through-beam. Up to 50 m sensing distance range, Vdc and Vac supply.
Ultrasonic fork sensors for label detection on transparent surfaces. Dynamic Teach- in system. Width slit detection 3 mm; maximum switching frequency 1,500 Hz.
For object or label detection; 2 mm to 180 mm width slit detection; 30 mm to 120 mm depth slit detection; red, infrared and laser emission; adjustable.
Adjustable and multifunction capacitive forked sensors with auto calibration for label detection.
This type of products is suitable for applications like labels detection and control, in particular transparent labels on transparent base. It can detect paper made and transparent labels, with thickness differences of few hundredths of millimeter.
The LABEL•EYE™ is a photoelectric sensor designed specifically to sense a variety of adhesive labels. Since the LABEL•EYE™ is an automatic one-touch sensor…not the conventional “teach mode” sensor…set-up is simple. Position the gap between the labels directly under the sensors sight guide and push the appropriate Autoset™ button. The sensor does the rest, adjusting itself to the perfect setting. Sensing labels has never been easier.
Offers a wide range of connectors that comply with the reliability and application requirement in the field of industrial automation.
Sentech Industries Co., Ltd.
43 Soi Rangsit-Pathumthani 12,
Prachathipat,Thanyaburi,
Pathumthani 12130,
Thailand
Tel: +66 2 567 4592
Fax: +66 2 958 4014
Email: sales@sentechindustries.com
18, Jalan BPU9
Bandar Puchong Utama
47100 Selangor,
Malaysia
Tel: +60 3 5891 1918
Fax: +60 3 5891 1919
Email: sales@technical-avenue.com
18 Boon Lay Way
#04-118 Tradehub 21
Singapore 609966
Tel: +65 8777 2818
Mobile: +6012 402 2818
Email: sales@technical-avenue.com
Technical Avenue Co. Ltd
First Floor, No. 9, Road 27,
Van Phuc Riverside City, Hiep Binh Phuoc Ward, Thu Duc City,
HCMC, Vietnam
Tel: +84 9624 62398
Fax: +84 8880 89582
Email: salesvn@technical-avenue.com